Samson DOUBLE BRAID Class I Back Splice Instrukcja Użytkownika Strona 2
- Strona / 2
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
PAGE 2 OF 2
Double Braid Class I Back Splice
SAMSON SPLICING INSTRUCTIONS
ADJUSTING THE CORE OVER COVER
BURYING THE EXPOSED CORE
5
step
Remove tape from cover end. Cut cover
strands at an angle to avoid blunt end.
Smooth core from Mark 2 toward Mark 3
until cover ends just disappear inside.
Next, holding core at Mark 3, smooth core
from Mark 3 to Mark 2. Do this until all
excess is eliminated.
Hold rope at slipknot and with other hand,
milk the cover toward splice, gently at rst,
and then more rmly. The cover will slide
over Mark 3, Mark 2, and nally Point X.
Be sure all excess cover is milked out so
that Point X (which will show as a bump)
is well inside the cover.
If nal burying is difcult, ex the splice
back and forth to loosen the strands, then
continue burying.
Cut the protruding core off close at the cover. Once again milk
cover rmly towards the end so that it covers the cut off core.
6
step
7
step
FINISHED SPLICE
End of buried section
Finished Back Splice
Cut core end off close to rope end
core
Mark 1
Smooth core excess from Mark 3
to Mark 2 toward Mark X
Smooth core until cover end
just disappears at Mark 3
cover
X
Taper cover by cutting
the end at angle
core
X
Beginning at slipknot “milk” cover by sliding
hand toward X
Insert d into core at Mark 2. Slide d
through and out at Mark 3.
Pinch taped end of cover, jam it tightly into
hollow end of d. Hold core lightly at Mark 3,
place the pusher point into the taped end,
and push d and cover through from Mark 2
and out at Mark 3. When using wire ds for
larger size ropes, attach d to taped cover.
After d is attached, milk the braid over the d
while pulling d through from Mark 2 to Mark 3.
4
step
PUTTING THE COVER INSIDE CORE
cover
Pinch taped
end to
Mark 2
insert
in fid.
Mark 1
core
Mark 3
X
DOCUMENT DblBrd_C1_Back Splice_AUG2012.pdf
© 2012 Samson Rope Technologies, Inc. All rights reserved. S/WD #108294 7/2012
1
2
Powiązane produkty i podręczniki dla Narzędzia Samson DOUBLE BRAID Class I Back Splice
Narzędzia Samson DOUBLE BRAID Class I Eye Splice Modified for Used Instrukcja Użytkownika
(4 strony)
(4 strony)
Narzędzia Samson DOUBLE BRAID Class II End-for-End Splice Modified Instrukcja Użytkownika
(4 strony)
(4 strony)
Narzędzia Samson DOUBLE BRAID Class II Eye Splice Modified for TS-I Instrukcja Użytkownika
(5 strony)
(5 strony)
Narzędzia Samson DOUBLE BRAID Class II Eye Splice Modified for Turb Instrukcja Użytkownika
(5 strony)
(5 strony)
Narzędzia Samson DOUBLE BRAID Class II Tips for Stripping the Cover Instrukcja Użytkownika
(4 strony)
(4 strony)
Narzędzia Samson DOUBLE BRAID Special Tips for Splicing Double Brai Instrukcja Użytkownika
(1 strony)
(1 strony)
Narzędzia Samson DOUBLE BRAID Class II Eye Splice Modified for TS-I Instrukcja Użytkownika
(8 strony)
(8 strony)
Narzędzia Samson DOUBLE BRAID Special Tips for Splicing Double Brai Instrukcja Użytkownika
(1 strony)
(1 strony)
Ebm-papst W4D500-GM03-10 manuales
Manuales del propietario y guías del usuario para Hardware Ebm-papst W4D500-GM03-10.
Ofrecemos 2 manuales en pdf Ebm-papst W4D500-GM03-10 para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji