Samson 12-STRAND Class I Eye Splice Instrukcja Użytkownika Pobierz pdf (Strona 1)

PAGE 1 OF 2

SamsonRope.com | Email [email protected] | Tel +1.360.384.4669

12-Strand Class I Eye Splice

SAMSON SPLICING INSTRUCTIONS

1 ﬁd

Class I ropes are made from any or all of the following bers:

olen, polyester, or nylon.

The eye splice is used to place a permanent loop in the

end of a rope, generally for attachment purposes to a xed

point. An eye is also used to form the rope around a thimble,

which is used to protect the rope, especially when it is to be

attached to a shackle, chain, or wire rope.

This eye splice may be performed on new or used rope.

This is an all-purpose splice technique designed for people

who generally splice used rope as frequently as new rope.

By following the procedure below, the splice can retain

from 90% to 100% of average new rope strength and,

in used rope, up to the same proportion of residual used

rope strength.

step

Tape end of line to be spliced and

measure 1 tubular d length (or 2 wire

d lengths because wire ds are half the

length of tubular ds) from taped end of

line and make Mark 1.

From Mark 1 measure 1 tubular d

length (or 2 wire d lengths) and make

Mark 2. Now form size of eye desired

and make Mark 3.

Form size of

eye desired

Mark 3

Mark 2

1 ﬁd

Finished splice

Mark 1

2 wire ﬁds

MEASURING

3 strands (or pairs of strands), right and left,

pulled out and cut off

Mark 2

Mark 1

Retape end to

stop unbraiding

Splice, loop, etc.

step

From Mark 1, in the direction of the taped end of the line, mark every second right and

left strand* for 3 strands.** Pull every marked strand out of line and cut off (tape at end

can cause resistance and may have to be removed in order to pull out cut strands.)

Tapered end will now have only 6 strands remaining (or 4 strands for an 8-strand braid.)

Tape tapered tail tightly to keep from unbraiding.

step

Mark 3Mark 4

ﬁd

Mark 1

2 ﬁd

lengths

Tapered tail

Push

Measure 2 tubular d lengths

(4 wire d lengths), make Mark 4.

Insert d and tapered tail at Mark

3 and push out beyond Mark 4.

MAKING TAPER

BURYING TAIL INTO STANDING PART OF LINE

*Some rope diameters may have pairs of strands in

right and left direction. In this case, treat the pairs

of strands as a single strand, marking and cutting

both in each direction as described above.

**Some very small diameter ropes may be 8-strand.

For an 8-strand construction, mark every 3rd left

and right strand for 2 strands.

Mark 2

1 2

Podsumowanie treści

Strona 1 - 12-Strand Class I Eye Splice

PAGE 1 OF 2SamsonRope.com | Email [email protected] | Tel +1.360.384.466912-Strand Class I Eye SpliceSAMSON SPLICING INSTRUCTIONS1 ﬁdClass I

Strona 2 - Lock Stitching Procedure

Komentarze do niniejszej Instrukcji

Brak uwag

Samson 12-STRAND Class I Eye Splice Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Narzędzia Samson 12-STRAND Class I Eye Splice. Samson 12-STRAND Class I Eye Splice User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Samson 12-STRAND Class I Eye Splice Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Narzędzia Samson 12-STRAND Class I Eye Splice. Samson 12-STRAND Class I Eye Splice User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Narzędzia Samson 12-STRAND Class I Eye Splice