Samson 12-STRAND Class I Eye Splice Instrukcja Użytkownika Strona 2
- Strona / 2
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
© 2012 Samson Rope Technologies, Inc. All rights reserved. S/WD #108294 7/2012
DOCUMENT 12Strand_C1_Eye Splice_JUL2012.pdf PAGE 2 OF 2
12-Strand Class I Eye Splice
Lock Stitching Procedure
SAMSON SPLICING INSTRUCTIONS
Mark 3
Mark 2
Mark 4
Smooth
Tapered tail
Standing part of rope
Pull
4
step
Remove d. Pull hard on tapered tail
with one hand. With other hand, smooth
bunched line towards eye splice until
Marks 2 and 3 converge.
5
step
When nished, Mark 2 and Mark 3 should be at the same point in
the vertex of the eye—which yields desired eye size. To nish eye
splice, the splice must be lock stitched (procedure follows).
Pull out marked strands and cut off
Mark 3 consecutive strands
FINISHING BURYING
FINISHING EYE SPLICE
Finished splice
4A
4B
Remove the d and any tape
at the end of the tail. From
the end of the tail, Mark
3 consecutive strands, as
shown. Pull them out of the
braid and cut off close to the
body of the rope.
Now, using both hands and
the weight of your body,
smooth the cover slack from
Mark 3 towards Mark 4. The
tail will disappear into the
rope, and a smooth, gradual
taper should result.
Mark 4
STEP 4
After completing Step 3, rotate spliced part of rope 90° and reinsert
end A into spliced area in the same fashion as in Steps 1, 2 and 3.
The splice will now be stitched on 2 planes perpendicular to each
other. Make sure you do not pull the stitching too tight.
STEP 5
After stitching at least 3 complete stitches as in Step 3, extract both
ends of the twine together through the same opening in the braid.
Tie them together with a square knot and reinsert back into braid.
For double braids, re-insert the knot between the cover and core.
B
A
A
B
1
23
A
B
123
A
B
STEP 1
Pass stitching twine through
spliced area near throat of
eye as shown.
STEP 2
Reinsert twine through the
rope. The twine should
cover 2 strands from the
exit point. Pull the twine
snug, but not tight.
STEP 3
Continue to reinsert as
shown until you have at
least 3 complete stitches
on each side of the rope.
Each stitch should cross
over 2 strands in the rope.
1
2
Powiązane produkty i podręczniki dla Narzędzia Samson 12-STRAND Class I Eye Splice
Narzędzia Samson 12-STRAND Class I Eye Splice Modified for Quik-Spl Instrukcja Użytkownika
(2 strony)
(2 strony)
Narzędzia Samson 12-STRAND Class I Whoopie Sling Modified for Tenex Instrukcja Użytkownika
(2 strony)
(2 strony)
Narzędzia Samson 12-STRAND Class II End-for-End Splice Modified for Instrukcja Użytkownika
(4 strony)
(4 strony)
Narzędzia Samson 12-STRAND Class II Tuck-Bury Eye Splice Modified f Instrukcja Użytkownika
(3 strony)
(3 strony)
Narzędzia Samson 12-STRAND Class II Tuck-Bury Eye Splice Modified f Instrukcja Użytkownika
(3 strony)
(3 strony)
Narzędzia Samson 12-STRAND Class II Whoopie Sling Modified for AmSt Instrukcja Użytkownika
(2 strony)
(2 strony)
Narzędzia Samson DOUBLE BRAID Class I Eye Splice Modified for Used Instrukcja Użytkownika
(4 strony)
(4 strony)
Narzędzia Samson DOUBLE BRAID Class II End-for-End Splice Modified Instrukcja Użytkownika
(4 strony)
(4 strony)
Ebm-papst W4D500-GM03-10 manuales
Manuales del propietario y guías del usuario para Hardware Ebm-papst W4D500-GM03-10.
Ofrecemos 2 manuales en pdf Ebm-papst W4D500-GM03-10 para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji